Description:

The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract with Lowest Price Technically Acceptable (LPTA) Evaluation Factors for the item listed below. The required item is for commercial items prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice.

The Contract Line Items (CLINs) is as follows:

CLIN 0001 QTY 280 EA

NOTE: Programming stations are stand alone and are not connected to any networks.

ORDERING DATA:

DETAIL SPECIFICATION: ACQUISITION REQUIREMENTS

6.2. Ordering data. Acquisition documents must specify the following:

a) Title, number, and date of this specification.

QQ-N-286G - 07 December 2000

b) Form, condition, and surface finish of material required (see 1.2.1 and 1.2.2).

Form 2, Finish A; ANNEALED AND AGE HARDENED

c) Issue of dodiss cited and if different than that listed in the dodiss, the specific issue of individual

documents referenced (see 2.1.1, 2.1.2, and 2.2).

N/A

d) Whether a forging sketch is required (see 3.1.1).

N/A

e) Size required (see applicable table).

f) If a product check analysis is required (see 3.2).

N/A

g) When hardness measurements may be utilized for forged rings and discs (see footnote 4 of

table III.).

N/A

h) When tolerances other than those specified are permitted (see footnote 2 of table VII; footnote 6

of table XV; footnote 5 of table XVI and footnote 2 of table XVIII).

N/A

i) If optional ultrasonic inspection is required (see 3.7.1.2)

N/A

j) If optional liquid penetrant inspection is required (see 3.7.2).

N/A

k) The lengths required and whether cut-to-length, random mill lengths, nominal (stock) lengths, or

multiples of specified lengths (see 3.9.1.3.1, 3.9.3.3.1 and 3.9.3.3.2).

N/A

l) If multiples of a specified length are ordered, whether a ¼ inch allowance should be made for

each cut (see 3.9.1.3.1).

N/A

m) If edges are other than specified (see 3.9.1.4, 3.9.3.4.1, 3.9.3.4.2, and 3.9.3.4.3).

N/A

n) Forging dimensions (see 3.9.2).

o) If marking should be other than specified (see 3.10).

N/A

p) When mechanical tests are required for rod and bar intended for reforging (see 4.3.2.2).

N/A

q) If mechanical testing is to be done on material ordered in the unaged condition, to demonstrate

its capability of being aged to meet the required mechanical properties, and, if desired, the heat

treating procedure to be used on the test specimens (See 4.3.2.2 and 4.3.2.2.1).

N/A

r) The final heat treatment procedure to be used on the lot before being placed into service and on

the slow strain rate tensile test specimens (see 4.3.6.1).

s) When the laboratory conducting the slow strain rate tensile test is selected by the purchaser

(see 4.3.6.4.4 ) Source: http://assist.dla.mil -- Downloaded: 2024-10-09T18:25Z Check the source

to verify that this is the current version before use. QQ-N-286G 35

t) Packaging, packing, and marking requirements (see 5.1)

OQE Ordering Requirements for CIM

Provide written verification that the chemical and mechanical properties have been determined and are

acceptable IAW the required specification QQ-N-286G as applicable for document 4283C063 are as follows:

a.) Provide written verification that the chemical analysis and mechanical properties tests have been

determined and are acceptable. All test reports will contain a signed certification that the results represent the

actual values for the material provided and that they are in full compliance with the contract specification.

Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and

signature of the authorized company representative. The name and title shall be clearly legible. Certification data

supplied to the government shall be either the original mill material certification, the original copy from the testing

facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed

certification that the reported results represent the actual attributes of the material furnished and indicate full

compliance with all applicable specification and contract requirements. Statements on material certification

documents must be positive and unqualified. The material certification data reports shall include quantitative data

representing th