This is a Sources Sought Notice only.  This is NOT a Request for Proposal or Request for Quote.  No Solicitation Number has been assigned at this time.  DLA Troop Support is seeking to identify possible sources who can supply the below item:

HEATER,AIR,ELECTRIC
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE
SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS.  FOR LARGE
ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE
APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON
REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RD002, COVERED DEFENSE INFORMATION APPLIES

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ003: CONFIGURATION CHANGE MANAGEMENT FOR EDGEWOOD FOR CHEMICAL,
BIOLOGICAL CENTER MATERIALS - ENGINEERING CHANGE PROPOSAL REQUEST FOR
VARIANCE (DEVIATION OR WAIVER)

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to
export-control of either the International Traffic in Arms regulations
(ITAR) or the Export Administration Regulations (EAR), and cannot be
exported without prior authorization from either the Department of State
or the Department of Commerce. Export includes disclosure of technical
data to foreign persons and nationals whether located in the United
States or abroad. This requirement applies equally to foreign national
employees and U.S. companies and their foreign subsidiaries. DFARS
252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control
technical data to DLA contractors that have an approved US/Canada Joint
Certification Program (JCP) certification, have completed the
Introduction to Proper Handling of DOD Export-Controlled Technical Data
Training and the DLA Export-Controlled Technical Data Questionnaire
(both are available at the web address given below), and have been
approved by the DLA controlling authority to access the
export-controlled data. Instructions for obtaining access to the
export-controlled data can be found at:
https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/

To be eligible for award, offerors and any sources of supply proposed
for use are required to have an approved JCP certification and have
been approved by the DLA controlling authority to access
export-controlled data managed by DLA. DLA will not delay award in
order for an offeror or its supplier to apply for and receive approval
by the DLA controlling authority to access the export-controlled data.

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NOR INCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BY THE
SPECIFICATION REQUIREMENTS.

    UNLESS OTHERWISE NOTED
FIRST ARTICLE TESTING IS REQUIRED

52.246-15 CERTIFICATE OF CONFORMANCE

FAR CLAUSE 52.246-11 APPLIES.  THE CONTRACTOR SHALL BE IN COMPLIANCE
WITH THE FULL REQUIREMENTS OF THE INTERNATIONAL ORGANIZATION FOR
STANDARDIZATION (ISO) 9001 STANDARD AT THE TIME OF CONTRACT ACCEPTANCE
OR CONTRACT MODIFICATION DATE.

1.  The minimum Higher Level Contract Quality Requirements for
manufacturers for DLA ISO 9001:2015.  MIL-I-45208 and MIL-Q-9858 are
obsolete and no longer acceptable when higher level quality is required.

2.  Higher-Level Contract Quality Requirement for Non-Manufacturers.  If
a non-manufacturer is supplying the material, the non-manufacturer
shall:

(i) Furnish items produced at a manufacturing facility conforming to the
higher-level contract quality requirement for manufacturers as specified
in paragraph 1; and

(ii)  Maintain and provide documented evidence that material furnished
under this contract was produced at a manufacturing facility conforming
to the specified higher-level contract quality requirement and that the
material meets all requirements.  At a minimum, the documented evidence
shall be suffici