CONTACT INFORMATION|4|N97113|FAA|717-605-5834|amanda.r.hayward.civ@us.navy.mil| ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|||||||||||||||||||| INSPECTION OF SUPPLIES--FIXED-PRICE (AUG 1996)|2||| GENERAL INFORMATION-FOB-DESTINATION|1|B| WIDE AREA WORKFLOW PAYMENT INSTRUCTIONS (JAN 2023)|16|Invoice and Receiving Report (Combo)|Inspection / Acceptance Point - Source|TBD|N00104|TBD|TBD|see schedule|TBD|N/A|N/A|TBD|N/A|N/A|N/A|N/A|navsupwawf.wss.ftc@navy.mil| NOTE FOR CONTRACTOR/ADMINISTRATIVE CONTRACTING OFFICER|3|||| NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (OCT 2020)(DEVIATION 2020-O0008)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13|||||||||||||| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (JAN 2025)|13|32550|550|||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||X| 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture of the ANTISEIZE COMPOUND . 2. APPLICABLE DOCUMENTS - NOT APPLICABLE 3. REQUIREMENTS 3.1 Manufacturing and Design - The ANTISEIZE COMPOUND furnished under this contract/purchase order shall meet the material and physical requirements as specified ;on part number MILT83483-8OZTU cage 81349; . 3.2 Marking - Unless marking requirements are specified by a document or drawing cited in this solicitation all items delivered under this contract/purchase order shall be marked and identified in accordance with the applicable Military Standards and Specifications as follows: Mechanical Parts, Assemblies and Equipments - MIL-STD-130 Electrical and Electronic Parts - MIL-STD-1285, Method 1. Electrical and Electronic Parts and Assemblies not covered by MIL-STD-1285-use MIL-STD-130. Electronic Equipment - MIL-STD-454 Requirement Number 67. Electrical Equipment - MIL-P-15024/5 (SHIPS) 3.3 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 3.4 SHELF LIFE REQUIREMENT - The following is excerpts from DOD 4140.27-M Shelf Life Management Manual. This requirement is mandated by MIL-STD-129P referenced under the Preservation, Packing and Marking portion of this TDP. 2-12. 85 Percent SHELF-LIFE REMAINING REQUIREMENT APPLICABLE TO ACQUISITION/PROCUREMENT A. Acquisition/procurement documentation shall specify that shelf-life items/material will have not less than 85 percent (allowing for rounding to whole months) of shelf-life remaining at time of receipt by the first Government activity. Any delivery from a contractor not having at least 85 percent shelf-life remaining shall normally be considered non-conforming. Refer to Appendix E of this Manual to determine the amount of time that 85% equates to in terms of remaining shelf life for Type I or Type II shelf-life codes. B. In supporting imminent use or consumption, the 85% shelf-life remaining on receipt by first Government activity may be modified or adjusted as deemed prudent at the discretion of PMs and IMMs, when support alternative arrangements such as EC, PV, DVD or local purchase are effected. Use of support alternatives for shipment/delivery to storage facilities as stock will conform to the 85% rule. 2-13. CONTRACTOR MARKING. Shelf life items will be marked for identification and control. Markings, shown below the item identification data are required on all units, intermediate, and exterior packs or unpacked items, shall be per MIL STD 129, MIL-STD-130, MIL STD 290 (FSC 9150 only), or FED STD 123, (references (m) through (p)) respectively, and will include the following: A. For Type I shelf life items: apply one, as appropriate; date manufactured, date cured (for elastomeric and rubber products only), date assembled, or date packed (subsistence only); and expiration date. B. For Type II shelf life items: apply one, as appropriate; date manufactured, date cured (for elastomeric and other rubber products only), date assembled, and date packed (subsistence only), and inspect/test date. C. For both Type I and Type II markings in subparagraphs A and B above: the date shall be expressed by the numeric month and the last 2 digits of the calendar year; i.e., 06/95, with the day of that month being the last day. D. Different Dates on Identical Items. When two