U/W Body (Waterborne), Clean and Inspect, Renew Zinc Anodes 1. Scope 1.1 Intent. This work item describes the requirements for the Contractor to clean the vessel’s U/W body and to renew bolt-on zinc anodes, while the vessel is moored pier side. 1.2 Cutter, Address, Availability, and POC. USCGC WILLIAM SPARLING, 427 Commercial Street Boston, MA. 02109. Cutter Availability: 10 - 13 March, 2025. Cutter POC will coordinate service OOA 03 Mar 2025. EMCS Conrad Aguirre, Cell #: (310) 357-7465, Conrad.M.Aguirre@uscg.mil 1.3 Government-furnished property. MTI ITEM DESCRIPTION NSN/PN QTY ESTIMATED COST ($/UNIT) N Anode, stern tube P/N: Z0020202H3 NIIN: 016445483 28 ea. $11.15 N Nut, Self-Locking P/N: 90715A145 NIIN: 015085774 2 Bx *24 in a bx $7.24 N Anode, Sea Chest Grate P/N: GA-4 NIIN: 016476179 4 ea. $21.93 N Screw, Prop zinc plate P/N: 950756 NIIN: 016340210 8 ea. $9.42 N Screw, Sea Chest Grate Anode, P/N: 93190A634 NIIN: 016197182 4 ea. $9.70 N Screw Cap, Stern Tube Covers P/N: 90585A626 NIIN: 016161107 42 ea. $1.81 N Zinc plate, propeller P/N: 950733 NIIN: 016278941 2 ea. $618.85 N Anode, Bow Thruster, Gear Case, Bolt On P/N: 1081226 NIIN: 123561870 1 ea. $64.97 N Anode, Bow Thruster, Tunnel, Bolt On P/N: CM2000Z NIIN: 200126334 12 ea. $29.46 2. REFERENCES COAST GUARD DRAWINGS Coast Guard Drawing 154B WPC 111-301, Rev A, Shell Expansion Coast Guard Drawing 154B WPC 161-301, Rev -, Skegs and Stern Tubes Support Structures Coast Guard Drawing 154B WPC 562-201, Rev -, Rudder Details Coast Guard Drawing 154 WPC 565-201, Rev -, Fin Stabilizer System A & D Coast Guard Drawing 154B WPC 568-201, Rev B, Bow Thruster System A & D Coast Guard Drawing 154 WPC 997-302, Rev -, Docking Plan COAST GUARD PUBLICATIONS Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2022, General Requirements Surface Forces Logistics Center Maintenance Procedure Card B10015.D (MPC B10015.D), 10/31/24, Insp/Cln U/W Equipment (Hull Plate) Surface Forces Logistics Center Maintenance Procedure Card B10018.D (MPC B10018.D), 5/31/23, Replace Underwater Zinc Anodes OTHER REFERENCES None 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. None. 3.1.2 Tech Rep. Not Applicable. 3.1.3 Protective measures. The Contractor must furnish and install all protective coverings to seal off and protect all non-affected vessel's components, equipment, and spaces near the work area against contamination during the performance of work. Upon completion of work, the Contractor must remove all installed protective measures, inspect for the presence of contamination, and return all contaminated equipment, components, and spaces to original condition of cleanliness. 3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). 3.2 Requirements. The Contractor must: 3.2.1 Video recording. Submit video highlights of underwater body surfaces (e.g. bow thruster, propellers, rudders, transducers, heavily fouled hull areas, etc.) before and after cleaning. 3.2.2 Clean/inspect. Clean the U/W body surfaces free of all marine growth, debris, and all other surface contaminants in accordance with MPC B10015.D. Remove and replace sea chest grating if necessary to access/clean sea chest suction. Ensure all transducer surfaces are cleaned with only hand held brushes, without the use of power attachments. Ensure that existing u/w body coating system or non-coated surfaces do not incur any damage during cleaning process. Polish propellers. Refer to Coast Guard drawings listed in Section 2. 3.2.3 Renew anodes. Renew Government-furnished components listed below paragraph 1.2. in accordance with MPC B10018.D

NOTE: The USCG/Government reserves the right to Award on an All or None Basis that is the Government may issue a Purchase Order (PO) to the Offeror that submits the lowest aggregate price rather than issue a Purchase Order to each Offeror based on the lowest Quotation on each item.

As stated below, the provision at FAR 52,212-2, Evaluation-Commercial Items-applies with the following addenda:

Award of a contract will be based on the following criteria: The purchase order will be awarded as a firm fixed price contract using simplified acquisition procedures in accordance with FAR Part 13.5.

       1. Please provide any warranty information.
       2. Vendors MUST be registered in www.sam.gov

The USCG/Government intends to award a purchase order resulting from this synopsis/solicitation to the responsible contractor whose quote conformed to the solicitation which will be most advantageous and the Best Value to the Government, price and other factors considered.

Please Note: Interested Offerors having the expertise as required are invited to submit a Firm Fixed Price quotation that will be considered by the agency. Quotations must be submitted on c